Sensor LCD Display NOM11
This plug-In display is intended for integration into existing sensor connections.This display is compatible, depending on the variant, with all sensors, which have a 0 - 10 V or a 4 - 20 mA signal.Connecting the display is very simple as the original signal is passed through. Simply open the existing DIN 43650A connection, insert the display and close the connection again with the included longer screw.If the display has not already been configured, you can configure it now.Because the display causes a voltage drop of less than 3.5V, in most cases the supply voltage of the sensor does not need to be raised. An additional power source is not needed.Once the display is configured, it can be used as a quick monitoring tool in case of problems. Within a minute the display is installed, the measured value of the sensor is displayed and the source of the problem can be narrowed down.This way you can save valuable time solving the problem.Due to the low cost of the display it is economical to outfit an existing sensor with it than to have a manometer at a different connection.The display is equipped with background lighting, offering tireless readThe illumination of the display enables fatigue-free reading even in dark surroundings. Included: Display, with DIN 43650A connection: long screw as well as gasket as seen on the picturesConnection layout: DIN 43650A: 4 - 20 mA: 1: + 2: - 3: empty; 0 - 10 V: 1: + 2: - 3: signalThe display has to be configured by the customer.
Pressure gauge
Suitable for: Rotary vane vacuum pumps and side channel blowers Function: The pressure gauges are for example used to monitor the exhaust filters of the rotary vane pumps. Manometer size: ∅50 mm Pressure range: 0 - 0,6 bar Accuracy class: 1.6 (→ ±1,6%) Material: - Housing: steel sheet- Measurement system: brass Connection thread: G ¼" Options:(Connection thread) - original: G ¼"- with adapters: G ¾"
PUR cable for pressure sensors with M12 4-pole a-coded connector 5m
This cable is intended for our pressure sensor with M12 connectors. It features a 4-pole a-coded connector.The connector is available in a straight and an angled version.The cables are 5m long and have four wires with 0.34mm².The plastic mantle is made of PUR and therefore very durable. Pin layout:1: brown2: white3: blue4: black
Cable for pressure sensors with Packard-plug 5m
This cable is intended for the connection with our pressure sensors with Packard sockets.The Packard connection is simple, but also has a high protection class and a high connection retention.Another designation for the connection is Metripack 150.The cable is 5m long, has three wires with a vein cross section of 0,5 mm².
Vacuum manometer
Suitable for: Rotary vane and side channel vacuum pumps Function: The vacuum manometers are used for monitoring as well as setting the desired degree of vacuum. Available models: The manometers are available in various designs (vertical, horizontal), display sizes (63 mm, 100 mm) and both undamped and glycerin-damped. technical data: Class of accuracy: 2,5 / 1,6(*) Display range (rel.): (-1) – 0 bar Dim. of connection: G ¼“ (Ø63)G ½“ (Ø100) Scale division: 0,05 (Ø63)0,02 (Ø100) Material (housing): plastics / CrNi(*) Material (metering): brass Degree of protection: IP 42 / IP 65(*) * glycerin-damped version
Reducing nipple with aluminium seal outer thread 1/2 inner thread 1/4 for pressure sensors PT2
This reducer can be used if the PT2 sensors are to be fitted to a G 1/2" connection instead of a G 1/4" connection.Materials: Brass (reducer), aluminium (sealing washer)Temperature range: -40 ~ 150 °CPermissible pressure: 60 bar (reducer), 18 bar (sealing disc)Connection: DIN EN ISO 228-1