Reducing nipple with aluminium seal outer thread 1/2 inner thread 1/4 for pressure sensors PT2

This sensor was developed for economical pressure measurements. Beside the usual sensor applications, for example feedback for control systems or continuous surveilance, this sensor can also replace pressure switches due to the low costs. The sensor can be used to surveil a multitude of mediums due to the high quality of materials that have been used. Up to 80°C the sensor is temperature compensated to increase the quality of the results.Other options are available as special orders, different output signals with lower voltages for single board computers, other connections and different pressures.This pressure sensor is by default equipped with a three-pole Packard-plug. Suitable counterparts are our cable for immediate use, which can be used in the accessories tab or article number 12078090 of the Aptiv company.

This sensor was developed for economical pressure measurements. Beside the usual sensor applications, for example feedback for control systems or continuous surveilance, this sensor can also replace pressure switches due to the low costs. The sensor can be used to surveil a multitude of mediums due to the high quality of materials that have been used. Up to 80°C the sensor is temperature compensated to increase the quality of the results.Other options are available as special orders, different output signals with lower voltages for single board computers and different pressures. You can find this sensor with other electrical connectors under the tab similar products.This pressure sensor is by default equipped with a DIN 43650 A connection. Another designation for the connection is DIN EN 175301-803.Included: Sensor, connector with gasket

with DIN 43650A connection (18 mm). Another designation is connector following DIN EN 175301-803 This sensor was developed for economic pressure measurements. Beside the usual tanks of sensors, like feedback for regulating systems or for on-going surveillance, this sensor can, with the packaged display, also replace pressure switches. Due to the resistant materials, this sensor can be used with a multitude of media. Up to 80°C, this sensor is temperature compensated to increase accuracy.The sensors are available with 0.5% accuracy (f.s.) from stock.This set contains the sensor and the display NOM13, enabling the sensor to replace both manometers, pressure switches or other sensors with display.This combination offers two outputs for simulated switches for the user. Therefore the plug layout is changed to accomodate the two additional ports.Note: Display is not pre-configured.Package contains sensor PT2, display NOM13, plug with gasket and long screwAttention: The display increases the necessary minimum supply voltage of the system:Necessary supply voltage for sensors with 4-20 mA output: 16 - 30 V  

This sensor was developed for economical pressure measurements. Beside the usual sensor applications, for example feedback for control systems or continuous surveilance, this sensor can also replace pressure switches due to the low costs. The sensor can be used to surveil a multitude of mediums due to the high quality of materials that have been used. Up to 80°C the sensor is temperature compensated to increase the quality of the results.Other options are available as special orders, different output signals with lower voltages for single board computers and different pressures. You can find this sensor with other electrical connectors under the tab similar products.This pressure sensor is by default equipped with an M12 plug.

This sensor was developed for economical pressure measurements. Beside the usual sensor applications, for example feedback for control systems or continuous surveilance, this sensor can also replace pressure switches due to the low costs. The sensor can be used to surveil a multitude of mediums due to the high quality of materials that have been used. Up to 80°C the sensor is temperature compensated to increase the quality of the results.The sensor has been packaged with our display NOM11, giving it the ability to replace manometers or existing sensors with display.Note: Display is not configured This pressure sensor is by default equipped with a DIN 43650 A connection. Another designation for the connection is DIN EN 175301-803.Included: Sensor PT2, connector with gasket, display NOM11, long screwAttention: The display increases the minimum voltage of the system:Operating voltage for sensors with 0 - 10 V signal: 16 - 30 VOperating voltage for sensors with 4 - 20 mA signal: 16 - 30 V